sjweinstein

works as stated I have it insatlled on 5 pollers

We could REALLY use a correlation engine today. We have over 3500 WAN point over 12000 switch monitored too. the IPS in one of our data centers took a dive and failover to the other unit didn't work right. Long story short, SW generated alerts on everything sending emails to the NOC and telcom management. A correlation…

Same here, i reported as a bug. Also a scan scheduling option would REALLY be a big plus BTW I have an install question. Should IPAM be installed on all pollers or the just the primary?

SAN was specifically not recommend by the SolarWinds development engineer and DBA i spoke to

5 engines all suppose to have IPSLA, i will have to check only router i have a problem with as 2600

using 3.1 the problem is on the 2600 rotute not the switch,

in ios 12.4 if this is manually configured it does not show in cli 'sho run' It is only visible if you do cli "sh ip monitor config" What is interesting is if you use IP SLA to do the configuration it is part of the normal sh run. why? Also when I configure IP SLA for type HTTP manually on a router it has some additional…

I believe that you are correct we have 1 primary and 3 additional pollers. One of our requirements was a single web interface for the NOC to see everything. What we did was split out the assigned poller based on our business grouping to try and balance the load to 10 K devices per poller. So then should I be more granular…

more votes for Meru 3500 AP 100+ sites with primary and secondary controller as of 12/31 planning on doubling that this year

Thanks for the response. Do you have any time frame? I really do not want to have to renew AirWave. The MIBS are all there in NPM already ,the MIB walk I did showed all of the info needed is there 

I just found this thread while looking up the same error condition. I just upgraded to toolkit 10.6 yesterday, running most current version of NCM. Last night all of our data center backups failed with "ERROR: Cannot download Running config : Cant download config. Probably TFTP Server is configured to Transmit only" How do…

I checked that with SW support and was told to use the NPM syslog and trap and to disable NCM as we were a) integrated b) using NPM alerts to send alert messages

I do not run APM but had similar problem with NPM after (9.5 to 10.0 and again with 10.0 to 10.1. On some our pollers 3 t obe exact, we have 6, i had to go and put the application path in in qoutes in the registry for some reason yet on the other 3 it was not a problem. If it helps the casee on this is 210446

What would be REAL nice is a drop down combo box, thau listed the groups, on the properties dialog box, where one could assign subnet to a group

we use HP "A" series switch and would k=like to see those supported

latest rev if IP sla 12.2.46a version where it is still configured with rtr cmds

them something is wrong as it will not let me do that

Just tried the discovery feature, need an explanation of what/how it discovers. I have about 20 device configured fro IP SLA but it found over 161 devices. Unless another engineer has been playing with IP SLA and not telling me. Also when it does the discovery it said the R/W snmp string was wrong, i can accept that as we…

I also want to add my voice for support of Meru AP and Controllers. We have implemented a campus wide environment in our 2 HQ locations, multiple controllers and about 1000 APs and have also started upgrades at 200 sites with N+1 controllers and and average of 25 APs and future plans fro more. So the sooner the better.

Not quite 4 server running NPM, of them also running NCM, 1 of them running NTA and then 1 doing logging , a dedicated DB server with one instance. Also the net mapping tool is also installed and one has engineers tool set installed. I think the advice provide to the person that set this up was not the best. If I…

here is what i put together for a switch model what still doesn't work right is tenet access. it takes for ever. a packet capture shows that SW is sending a CLI entry but then waits for a timeout for each line. I have also sent the complete MIB for Huawei to SW, just waiting fro them to compile name the file HUAWEI…

I ran the install routine on each poller

no discovery log there, no logs from today at all

perhaps I am something. But I would like to see the ability to add and delete devices by specific ip or host anme

How about more tabs for the operations, not just web, voip and top 10 As there are check boxes filtering what to display additional tabs shouldn't be tha much more to code

yep, slow and cumbersome when you have a class A and 6 class B to manage. Sw needs to add a drop-down combo box on the sublet properties that lists the defined groups and let one assign the subnet to the group

Support for HP "A" series switches Also a filter option on import jobs from NPM so we can be selective in wha goes into NCM. For example we have to moinitor APC UPS used with all of the routers but the import job pulls them into NCM so i have to create filters on the backups jobs to keep them from appearing as errors in…

Support for HP "A" series switches Also a filter option on import jobs from NPM so we can be selective in wha goes into NCM. For example we have to moinitor APC UPS used with all of the routers but the import job pulls them into NCM so i have to create filters on the backups jobs to keep them from appearing as errors in…

Cisco ASR routers show up as a generic Cisco As they have 2 processor you need to have CISCO-RTTMON-MIB http://www.cisco.com/en/US/docs/routers/asr1000/mib/guide/asr1mib3.html Can we get the MIBS updated and i the case of the ASR we need to see ESP, the second processor

we need these mibbs added to poll stats on Cisco DSP resources CISCO-DSP-MGMT-MIB CISCO-DSP-MGMT-CAPABILITY-MIB