Comments
-
Hello Michal, How i can monitor ipv4 and ipv6 traffic separately? I have one physical interface, on which both ipv6 and ipv4 addresses are configured. Now i want to monitor traffic flow of both ipv4 and ipv6 separately , just to know the usage of ipv4 and ipv6 traffic on my network . By default NMS dont show any difference…
-
Hello Michal, Any update ?? My evaluation period will be end in 3 days. Regards,
-
Thanks Martin for your help. I would try to do following steps: * try to restart the device * check whether there is new firmware (it may contain some NetStream-related fixes) * open support case with Huawei So right now NE80e is working properly with NTA , I have not checked NE40e yet, and NE20e has some OID translation…
-
Hi Martin, I have upload the file as requested by you. Root OID filed '1.3.6.1.4.1.2011.5.25.110.1.2.1.2' is giving no output and file (ifIndex) is saved empty. 1 into 'Root OID' field is giving output and file is saved as fullWalk.txt. Regards,
-
Hello , ipv6MIB (1.3.6.1.2.1.55) MIB file is uploaded on LEAPFILE as requested by you. Regards,
-
Hello Michal, I am evaluating NPM 10.2 , so can i open Support Ticket ?? I have upload the requested SNMP walk file on below link: http://solarwinds.leapfile.com (Huawei-NE80E-wakhan- SNMPWALK.zip) Almost all the file contain 1.3.6.1.2.1 mib but the last OID in the walk is not bigger than 1.3.6.1.2.1. I have stop the walk…
-
I have upload both files as requested by you. Now waiting for your reply. Regards,
-
Hello Michal, To get SNMPWALK of my router I put 1 in ROOT OID and start scan , and now its is continuously scanning from last 12 hours, so far it has scan 1454000 OIDs and still running. Is it normal behavior or i have to stop it manually ? Regards,
-
I just reconfirmed 16 Mbps – AVG(InterfaceTraffic.In_Maxbps) 54 Mbps – is coming through raw data , i apply AVG function on In_Maxbps column.
-
Is there is any easy built-in method to do this ?? i have 100 servers under different administration , how i will configure all of them . Please tell some easy and short method. Regards Waqas Ahmed
-
Hello Mav, Thanks for your reply. Below is the Huawei netstream configuration for NE20e Router Seires. I have also check netstream on Huawei Ne80e routers with solarwinds and its working. But we want to run netstream on NE20e as well. ----------------------------------------------------------------------- NE20E…
-
Hello aLTeReGo, Are you sure we can install Exchange Management Tool on Windows 2008 SERVER R2 ? Because as per your given link here Windows 2008 server R2 is not mentioned in the list. which operating system do you normally suggest for installing APM and NPM ??? I am getting below mentioned error :…
-
Thanks for reply .. I already know this, that in 10.2.2 , we can do this . But how i can do this in 10.0 , because due to limitation we cannot upgrade right now. Any other technique or some sort of script ???
-
Hello All, Thanks for your reply. The device is Huawei NE80e. If i run display ip interface brief command on router than it shows the status of the interface as ADMIN = UP , OPERATIONAL = DOWN. But if i run display ipv6 interface brief than interface status is ADMIN = UP and OPERTIONAL = UP. So i think NPM is by default…
-
waiting for response .
-
Dear PavelSrot, Thanks for your reply. I am using below mentioned query in Report Writer. If i filter result based on NodeID and Interface ID , the result is same. And the Average value is not correct. But if i take raw data from chart for specific interface and then manually takes its average than the values is different.…
-
Can we use Shibboleth SP with Orion ?
-
Our NPM's HOME PAGE ANOTHER MY FAVORITE
-
Hello All, Any update on this , I am also facing the same issue. I have manually set the interface bandwidth from EDIT INTERFACE button under interface. But in REPORTS it is still showing the default bandwidth , not the manually set bandwidth . How i can see manual set bandwidth in reports?
-
Waiting for response ... please help .. its urgent ..
-
Any update on this issue?? I am also facing same issue. Hyper V servers running Microsoft Windows Server 2012 R2 the statuses are not being displayed and we get a "Host Status: Could not poll" message.