sja ✭✭✭✭✭

Hi shashi.divi​ If that a 7360 ISAM PON cards is not supporting MiB2 like ethernet. You can poll the Router side ( Timetra) and get the stat from the NT cards and the backplane. There are other PON counters but they are not MiB2. Best regards SJA

1.3.6.1.4.1.2636.1.1.1.2.126 Juniper acx5048

I agree 100% "Bread and butter" like snmp trap and syslog run parallel to the main alert engine Shame...to call that SNMP TRAP /SYSLOG support when it's run as it does... Bugs that are not getting fix in "timely fashion" FR for bugs fix? /SJA

Stop every thing run the wizerd first on the primary, additional polling engine. Start the primary start the additional polling engine. If you sending traps to your setup that could be relavant /SJA 

Sure I run into the same thing with Juniper and Cisco HW changes we backup the output of the command that gives the results you need.. Device template not for backup configuration.. Cisco Devices template with "show Module"

Hi Not sure what are you looking for.. Google in thwack give those 2 variables in config change template for juniper MX Junos Routing Instance NCM scripting @ Sign

They can close your FR?about time ? Created on Jun 3, 2014 5:05 PM by Andy McBride - Last Modified: Jun 3, 2014 5:05 PM

Hi Alex I can say wellcome to the club :-( It's all about the topology and it's not working 100%. NPM can see my Juniper XE interfaces but not AE interfaces.... With that topology solution you can't have "backhaul" interface or 1 link on map.. for short the feature is useless /SJA

"unknown" ALU 7342 1.3.6.1.2.1 BARCO 1.3.6.1.4.1.1482.20.3.2.2.2

Hi millenium7​ I don't use that feature but can use as work around... "RTCD" "should" auto download your config with change syslog/trap from the node. https://support.solarwinds.com/Success_Center/Network_Configuration_Manager_(NCM)/NCM_Documentation/NCM_Administrator_Gu… i will agree that the compliance flow should have…

Hi jwfulford​ This is the out of the box poller that came with 12.3 Create standard alert that look for “events” that match “%replace%” the poller is pushing ups events to events log /sja

Hi I have a VM poller with 2 CPU 4 Gb RAM and 8000 elenents on the poller The CPU is around 20% the RAM is about 3 Gb. No syslog or Trap I dont poll inteface /node stat every 120 sec. /SJA

hi I run into the same problem. kiwi canot be in that filter and forward spot right now. https://thwack.solarwinds.com/ideas/1489# My work around is to send my traps to my test/dev npm sl100 server den forward the traps i need to my prudaction NPM.

Colud be nice if solarwinds will finally do something about SNMP TRAP Many just move trap out from Orion that FR could help if you move trap to kiwisyslog

Hi Jeff By what du you mean support ?:-) From what I can read/know TR-069 is HTTP SOAP appl. that communicate from your OSS/BSS to the WIMAX/LTE CPE right? 1.Solarwinds NPM can monitor with help of SNMP/ICMP/WMI that server that run TR-069 service. 2.NPM can monitor the VLAN/VRF/IP that service use to communicate. 3.SAM…

Take njoylif​ word that should work just fine.. but.. If your network is chatty or there are many different zones that are separated Kiwisyslog could be the answer... I use kiwisyslog as a filter layer and forwarding proxy to NPM NPM is not the best tool in the market for SNMP TRAP or Syslog (and I being nice) Do your…

Hi noki42​ In many times snmp inventory is not good enough.. If you can get the inventory output with cli commands use backup job. https://thwack.solarwinds.com/thread/112401

Hi Thanks for getting to me. Each POP/Site have 5-10 nodes that share the same address CP. Like to Auto generate those group based on that Address CP. something like Node A CP NY Node B CP LA Auto Group = 1.Group NY Node C CP NY 2.Group LA Node D CP LA /SJA

‌hi youtube is your friend https://m.youtube.com/watch?v=r9m0fvmfZlc

‌Hi The only time I had High CPU its was topology layer 2-3 try to disable its for 24 hours and see if it clear ...

Hi did you try nortel optera?or something wdm we had long ago optera 5200 very nice box.

Hi Before open a ticket with support. make sure that your cisco and Garrettcom are supporting those mibs that needed with that tool :\Program Files (x86)\SolarWinds\Orion\PollerCheckerTool If yes. Try to enable LLDP on Garrettcom & Cisco so they run the same disco protocol. Then if it's still not working make a ticket.

Hi andy12345​ The “old Best practices” is to minimize syslog and trap traffic to your Solarwinds deployment. Building a Large-scale SolarWinds Installation https://m.youtube.com/watch?v=SdUJ47f463w But with Log Analyzer (Formerly Log Manager) You could push more of that traffic to that deployment ...

Hi 212​ I have have something close I think.. The APC smart UPS I use work with 1.3.6.1.4.1.318.1.1.10.1.3.3.1.4 Try that poller

Hi It's should be ready in 11.5.X NPM 11.5 BETA4 + QOE NOW AVAILABLE

Hi I think its more on the vendor mib den solarwinds not all telco vendor have good mibs. Rad is "old hands" so they should have ok mibs. air interface: if its 1 oid you need to pool for the air interface power that will be very easy to monitor with universal poller ....

hi We have 3 VM poller 2 CPU 2.8 16GB RAM working just fine. NPM 11.5.3 NCM 7.4.2 what are your polling settings? /SJA

Hi What in : 6.General web performance improvements for larger customers? But any how its look good...

Yes that what VNQM support right now.. That the road map page What are we working on post VNQM v4.2 (Updated April 2, 2015)

Google is your friend.. Re: Report Writer - Query IP Helper Address