kumar07

@"superfly" after adding new poller for Aruba Stack switch i'm not able to found stack properties in customize views 

@"brscott" Yes, the nodes are monitoring through SMNP. Yes, this is a new additional pilling engine introduced in same orion environment.

@"superfly" I have created a poller for Aruba Stack switch after which I am able see stack properties but after few days when I check those switches I'm not able to found stack properties for the same. Any suggestion on this it will helpful for me.

@"sum_giais" What we have previous set up or ports open for old polling engine I have done the same thing for new polling engine as well and traffic has been allowed (source to destination) from firewall to new polling engine no luck i'm unable to migrate to new polling its showing test failed.

@"jm_sysadmin" I have restarted all the services still issue persists do you have any other solution for this.

@"superfly" We are using Aruba 3810 switches, when added switches into Solarwinds its not showing stack properties Node customize view.

@"alansmith" , As we can seen in console top 10 conversation history with the specific interface , same way i need to populate the data in report as well. Please help me in this.

@"alansmith" Yes, netflow is configured on selected interface, while selecting specific object. In table layout section i'm confused which data need to selected in column section . Could you please help me , i need this data to display in my report

@"superfly" Thanks for your response , As you mentioned above steps I have followed all the steps while, I searched the selected node I'm not able to enable the poller. In poller enable section is not active and scan status is showing not match.

@"deverts" All Switches are Cisco one. I have added into solarwinds but not able to find stack properties.

@"jm_sysadmin" Thanks for your response, is there any alternative solution for without rebooting the server. Thanks in advance Kumar

Can anyone help me on this, still I'm not able to pull the data for more than two months. Thanks in advance

@"mesverrum" can you please help me out on this.

@"sreenathmp" Thanks for your response , i have created report for bandwidth utilization for an interface , i am looking for netwflow top conversation with specific interface, if you have any idea on this please do let me know. Thanks in advance

Can anyone help me in this .

Adding some points alerts are configured via UNDP pollers, as per my knowledge if we configured harware alert via UNDP pollers we can't disable from Current Hardware Health any suggestion on this. Thanks in advance

@"rschroeder" Thanks for your response, as you suggested to follow two steps, 1. You suggested to keep the system as idle after selecting the custom 3 month time interval in morning I will get the result. I just want to inform you when I selected the custom 3 month time interval I'm getting error as "Data is not…

@"alansmith" Yes, I am looking for netflow report for specific interface, and specific nodes not all node. I have attached below screenshot i need those details for few specific nodes. Thanks in advance

@"superfly" As u mentioned once we add stack switch in Solarwinds it will automatically detect stack switch, but i am not able to find stack switch option in customize page. Please help me on this.

@"superfly" Thanks for your response , could you please let me know if I will add swich1 with IP address mentioned in my scenario can the second switch1(stack switch) IP address was not mentioned) will automatically add into solarwinds.? Thanks in advance 

Yes, I am able to ping the devices also tried Tracert.

@"mesverrum" Thanks for you response, I ahve checked with security team port 161 has been enabled.

@"jblankjblank" we are using 2019.2 , I have tried multiple possiblities to overcome from this situation but couldn't found any solution for this. Please helpme on this to get retified.

Thank you for your response, but i am not able to found Current Hardware Helath in Node Summary page. Any idea how can i get this. Thanks in adanvace Kumar

@"jeepinandy58" Yes I agree in your statement before that i just want to let you know this is Aruba switches 3810 model as per my knowledge in solarwinds we don't have default poller for Aruba stack. For this I have created new poller for Aruba Stack switch and I have enabled it . As I mentioned earlier after creating new…

I have deleted the existing node and tried to add once , but i'm getting SNMP error, could anyone help me on this how can I sort it out this issue.