krishnamishra0786 ✭✭✭✭✭

If you want to monitor array, please use snmp rather than wmi or agent

In the expected result we can monitor only up and down status of ILO, Steps :- 1- create a same template with Https monitoring 2-in URL section u can assign the ip address only. 3- assign the same template to node. note - if you have number of physical node then it is not easy to configure the ILO ip against the node in…

I used the all query to get the correct report but unfortunately report is not correct, That's why i am asking to all of you to get the correct report and i have bit knowledge of SQL query. Let me know you are not really interested to get the same report. Where user is acknowledged on how many alERT in daily basis, and…

Thanks i am respecting your word But the given example o report os not fruitful If you really understand the requirement of report then pleade let us know the way to get the same report Thanks K

HI, I want to automate the same in my infra because some time we forget to add the interface or drive in monitoring and we face the big problem some time if the same in not under monitoring, per my thinking it is not possible to do list recourse on every node and check mark and then submit the details which is not under…

Unable to connect to the remote server We are getting the above error, Chad - please suggest so that we can enable the url monitoring. Thanks K

when i disabled the same alert, all active alert does reset, when i again enable the same alert, Again it trigger the alert in alert console, Please advise if i could do further work on same.

Hello Everyone, Anyone can help on this scenario, we reach at the moon by product level of solarwinds but still have not such a feature whether we can make a own labels.

when i put last column, which is working and showing the lots of event for h/w sensor. But the point is i would to capture only perticuller h/w sensor event - like "hardware sensor critical for usb direct access" i think filter is not working.

thanks - that sound like cause of issue. Going to upgrade the environment might be can help us to finish the index.

If u r using the wmi, u can not get because wmi have not feasibility to monitor the array, please snmp for array monitoring. Thanks

I tried everything but unfortunately get not success on ILO traps. Finally i use the Sam template and enable the ILO status monitoring... On 28 Jul 2017 11:52 p.m., "Krishna Mishra"

Hi, Please use Sam template as with DNS entry like i$(dns)... And enable the monitor of ILO as an https Thanks K On 28 Jul 2017 11:48 p.m., "jm_sysadmin"

Hi Jeremy Actually same details were given by Alex and same is not useful because I am creating the report based on event(netperfmon event log ) and you are referring to us for trigger alert if I am using this it is not giving the required information, 1- everyday number of alert is triggered, by event log we can identify…

Hi Alex, These alert are working based on event log, and as you advise that trigger alert and event have not any co-relation, then this would be work, Could you please advise to solarwinds support team so they can help us also on this report. by the way i worked with team and they have advise us they are not supporting the…

HI Cahunt, could you please suggest us, if you did any investigation on same.

If VM goes to reboot, then alert is not triggering for esxi reboot, Issue with ESXI node last boot changed, may i know what solarwinds is checking whenever any esxi node goes to reboot. because whenever we restarting the snmp service of any esxi node, we are not getting the not reboot alert. i checked and test the same.…

As i am sure, Script will run by local host, and i tested the above script from Orion server (PS IDE), which is working fine, but we need to set the variable hostname instead on IP, So script can pic the hostname and give the result as expected. #ILO details $user="Administrator" $passwd="password" $ilo = "1x.x.x.x" #…

yes, Hp ILO CMD is installed on the Orion server. But when we are selecting the remote host, it require an additional setting like below, do we need to some additional config on ILO Server

when i disabled the same alert, all active alert does reset, when i again enable the same alert, Again it trigger the alert in alert console, Please advise if i could do further work on same.

Support team would not have any special magic they are always denied for any work, this feature is not available or this is feature request, I heard number of time from him, you would not be belive i have number of case where they don't have solution. And they are refering to thwack, might be any champ will help you, Now i…

this is the case number - Case Update: 1228779 for solarwinds support team ...

I ran the direct query in DB and get the output which is not as i like, that's why i would like to you please find any work arround which can give us the correct output.

Hi, Is it possible to check, who unmanaged the application in node, because i tried to find, who did, but unfortunately i did not find, thanks in advance Thanks K

Hi, i created the UDNP poller and assign to one node where the output is correct but when i am creating the alert which is result is not fruitful, Could u please help us so that we can create a correct alert for BGP.

Hi, find the output of OID And below is the snapshot of alert condition i used the same as per your given details, but alert condition is not showing correct.

Logged a case where support team have not any resolution, always i noted from support end. We get always one revert, this is feature request or future release. but we can do these are thing by another way,, i need help on this Alex ,, will let you know. thanks..

i am using this, can you please verify and add same table in same query, Table details like - cpu memory, disk SELECT TOP 1000000 Nodes.NodeID AS NodeID, Nodes.Region, Nodes.Region_Country, Nodes.Office, Nodes.Caption AS NodeName, Nodes."System" AS System, Nodes.Server_Description AS Server_Description, Nodes.Company AS…

Hi, I used the alert trigger condition- But i think the condition would not giving the correct result. Thanks Krishna

find the below required details,