jhorng

Correct. If one was able to dictate the interfaces and it showing up with the "bandwidth loading" scheme like it was auto detected. For my use, I would only want that link to show up on that map. We're looking to make customer specific maps and different customers could be using different paths. If one side of the…

Manual creation of new links that aren't auto discovered between network devices would be awesome. Currently we have situations were GRE tunnels are being used, and they aren't detected by solarwinds for mapping purposes. Also, we're heavily using "ip unnumbered" on interfaces between network devices. When used on a parent…

Feature is needed if Report Writer is being deprecated

This feature would be really helpful in our environment as well. We have several VRFs with routes that would be good to look at and see if flapping.

I've been very fortunate to avoid the problematic releases so far. But until our backup solution is in place, I'll have to be more cautious.

Thanks for the update!

Ugh, sounds rough. Hope it goes well. Let us know how it goes!

Interestingly 2023.1.0 has been relatively stable. There are some bugs that I've manually dealt with such as the job engine not automatically starting after a reboot of the VM. But the CVEs are building up so 2023.3.0 is tempting.

2023.3.0 is out as of today. Who is going to be first to give it a try? :)

Did the following to get the install back on track. This is not on the advice of Customer Service. I found this out myself. * Restarted the primary server. * Cleared centralized upgrade locks* support.solarwinds.com/.../Orion-Additional-poller-APE-failed-Centralized-upgrade-in-progress * Had to fix "Configuration Wizard"…

Offline upgrading from 2020.2.6 HF5 to 2023.1 has gone sideways. I initially couldn't upgrade because NTA licensing was expired. Since we're not using it, I uninstalled NTA from the Primary Server but not any APE. I re-ran the installed and it allowed me to start the upgrade. It's been stuck at 57% for hours with no end in…

If you're talking about feature request, it would be good to understand what feature to request. The original question was asked over 3 years ago and I believe the SVI / NVE interface are good monitoring points for netflow.

The only other thing I can think of is make sure you switches are up to date code wise and firewalls. We've been successful with 7.0.3.I7 and mostly migrated to 9.3.7(a). Is there a firewall that is blocking SNMP? I'd try to do an snmpwalk to the switch in question to confirm that works.

How about the interface vlans (L2 and L3) associated with the overlay?

What are you guys/gals trying to monitor? The nve1 interface does show up as a monitor-able interface.

No issues here. Most of my network is N9Ks. Did you configure the SNMP user by putting in "snmp-server user X network-operator auth sha "key" priv aes-128 "key" "? I've found if you just try to copy the hash and deploy it everywhere then it doesn't work. When discovering, are you using the "Network Discovery" tool or are…

For some reason I cannot get this to work. It will always error out with "config too short" for the multiple contexts. I copied the existing template and added the few lines at the bottom of your example. I've also tried adding the UseMultipleDownloadCommands option without effect. I've had to do something like this to get…

So what further troubleshooting can be done if an edge is in the NodeCiscoCDPEntries table, but is not in the TopologyConnections table? I'm running 12.4 and the table columns have changed. I'm correlating SourceNodeID to MappedNodeID. In my case, nodeID 661 has a topology entry to 663. But 663 does not have a topology…

How can one check to see what version of agent is installed?

Unfortunately even while following your process, the additional polling engines consume 3GB+ of memory in 24 hours. I can confirm if I restart the Solarwinds.Cortex service, the memory leak is cleared for 24 hours

Unfortunately the query as a select instead of a delete came back with 0 records. I quadruple checked the query to make sure there wasn't any syntax errors. We are not monitoring any servers and only network devices, so don't know if the query was related to host based monitoring. I went ahead an shutdown the services and…

Not sure if you were replying to the general audience, but the 3 entries I mentioned were not on that list.

Just to be clear, there are many entries in the list in log viewer. What I'm interested in is if there is a way to change the text so I can see more than 13 entries on the page without scrolling down.

1.3.6.1.4.1.9.12.3.1.3.1955 cevChassisN9KC9336CFX2 1.3.6.1.4.1.9.12.3.1.3.1626 cevChassisN9KC9372PX 1.3.6.1.4.1.9.12.3.1.3.1485 cevChassisISR4431

Don't know if you're resolved the issue, but seeing this in our environment as well. Although this is with the Jan 9, 2020 HF.

Seeing this issue in 2019.2 HF1. Unable to perform a memory dump due to implementation in a closed network. Anyone else having issues on this release?