Comments
-
As an employee at a U.S. Federal agency IPv6 support is important to us. Current and future purchases must be IPv6 compatible.
-
The losing of the sorting was an oversight on our part. We're working on fixing it for an SP. In fact, it's what I'm working on right now. We very much realize that this is an important feature for everyone. Casey, Does SP1 for 9.1 restore the functionality of Gob's Syslog Parser? Thanks
-
Any problems with Gob's parser after moving to v9.1?
-
Disabling NetBIOS is standard here, it has not affected orion NPM, NTA, or APM at all. We are able to resolve all names via DNS.
-
We would like the TFTP server to be able to bind to and listen on more than one interface (each interface is on a different network). Then we can collect configs via TFTP on some isolated out of band network segments we have where routing all TFTP traffic to just one of the interfaces is not possible.
-
I assume that by disabling NetBIOS over TCP/IP then this behavior is stopped? I see no NetBIOS broadcasts.
-
Chris, Do you know now if 5.1 is able to handle the Dell Powerconnect 53XX and 54XX SSH quirks? We have a great many of these switches and will soon be trying out the NCM demo, but we want to know if it is working with these Dell switch models? Thanks
-
Chris, We would like NCM to be able to handle TFTP downloads/uploads from the three interfaces on our NCM system not just one. Is this planned for a future release, or is it possible now? Thanks.
-
This is the method I have been experimenting with. I have set units to Bytes, under the advanced options what should I set the Time Frame as? I am currently polling and collecting stats every 2 minutes. Thanks.
-
I don't see the new name resolution methods mentioned in the release notes (www.solarwinds.com/.../releaseNotes.htm). I suggest including more detailed release notes along with the software download (.zip file) for all products, updates, and service packs. I would also include more detailed installation instructions since…
-
Wasn't us, but we appreciate your effort to fix the issue. Thanks
-
Denny, I am not Craig651. I for one really do want to get this figured out. I just cannot figure out how to use the universal poller to be able to take a sample at time period 0 (a value of say 5 disk reads) then another sample 5 minutes later (perhaps 12 disk reads) and then calculate (12 reads minus 5 reads) divided by 5…
-
Case #92740"Thank you for contacting SolarWinds. There is not a way to make any adjustments in either the templates for the different devices, or the application itself to tell it there is not a start-up config on the devices in question. I would suggest unchecking the box to download start-up configs." Regards,SolarWinds…
-
Digi Passport Console Servers 1.3.6.1.4.1.8072.3.2.10 - (discovered as net-snmp)
-
I asked "Does the update from 5.5 to 5.5.1 reset the user account settings for NCM back to 'default view'?" since in the past an new install of NCM or NCM integration would set user account views in NPM back to the default settings. (This used to occur with new versions of NTA also). I mentioned that "We a have quite a few…
-
If I remove the line "<Command Name="Startup" Value="config"/>" will NCM show supported config types as only running instead of running and startup?
-
Yann, Worked great. Thanks!
-
Hello gpend, this is not implemented, I do not think that the Solarwinds Team has read or acted upon this feature request.
-
I think the upgrade procedure states you can only import a v8.5.1 DB into v8.5.1 of Orion and then upgrade to v9SP2. But you better check with Solarwinds to be sure. Good luck. We were facing an upgrade from 7.X but we just installed 9SP1 on our new server and added our nodes back in.
-
The only issue we have had with this SP (and every NTA SP in the past year) is that the NetFlow Traffic Analysis Settings for each and every user account have been reset to default. For some accounts we have different views or no view at all, so we must change them all back. Below is an example of an account that has been…
-
Don't know of anything besides AD user accounts. Where I work we would love to authenticate users via tacacs or radius. Most network shops use tacacs and radius so they could leverage that resource and really simplify account and password maintenance. I had hoped SW would include this soon...
-
I don't know where it is either. Hopefully after this bump somebody will respond.
-
Same problem. I am in MDT. Last XX Syslog Messages shows 6 hours ahead.
-
You may want to look at this:
-
ICMP nodes show up unknown, so it makes it difficult to define a "view by device type" for unknown nodes since it groups ICMP-only nodes in there too.
-
Geist rack mount PDU model RCM and RCU - machine type is Unknown 1.3.6.1.4.1.21239
-
Chloride ManageUPS 1.3.6.1.2.1.33
-
I am not sure how to do them all at once, but beware, after installing an NTA SP they are all reset to the default again :(