Thanks...But these aren't responding the OID for the devices I have.
What about the standard linux oid's? Are you sure you snmp strings are setup correctly?
Which OIDs are you talking about? can you list them out if possible.
Yes SNMP is correctly configured.
yes of course.
1 minute Load: .220.127.116.11.4.1.2021.10.1.3.1
5 minute Load: .18.104.22.168.4.1.2021.10.1.3.2
15 minute Load: .22.214.171.124.4.1.2021.10.1.3.3
percentage of user CPU time: .126.96.36.199.4.1.2021.11.9.0
raw user cpu time: .188.8.131.52.4.1.2021.11.50.0
percentages of system CPU time: .184.108.40.206.4.1.2021.11.10.0
raw system cpu time: .220.127.116.11.4.1.2021.11.52.0
percentages of idle CPU time: .18.104.22.168.4.1.2021.11.11.0
raw idle cpu time: .22.214.171.124.4.1.2021.11.53.0
raw nice cpu time: .126.96.36.199.4.1.2021.11.51.0
Total Swap Size: .188.8.131.52.4.1.2021.4.3.0
Available Swap Space: .184.108.40.206.4.1.2021.4.4.0
Total RAM in machine: .220.127.116.11.4.1.2021.4.5.0
Total RAM used: .18.104.22.168.4.1.2021.4.6.0
Total RAM Free: .22.214.171.124.4.1.2021.4.11.0
Total RAM Shared: .126.96.36.199.4.1.2021.4.13.0
Total RAM Buffered: .188.8.131.52.4.1.2021.4.14.0
Total Cached Memory: .184.108.40.206.4.1.2021.4.15.0
The snmpd.conf needs to be edited. Add the following (assuming a machine with a single ‘/' partition):
disk / 100000 (or)
includeAllDisks 10% for all partitions and disks
The OIDs are as follows
Path where the disk is mounted: .220.127.116.11.4.1.2021.9.1.2.1
Path of the device for the partition: .18.104.22.168.4.1.2021.9.1.3.1
Total size of the disk/partion (kBytes): .22.214.171.124.4.1.2021.9.1.6.1
Available space on the disk: .126.96.36.199.4.1.2021.9.1.7.1
Used space on the disk: .188.8.131.52.4.1.2021.9.1.8.1
Percentage of space used on disk: .184.108.40.206.4.1.2021.9.1.9.1
Percentage of inodes used on disk: .220.127.116.11.4.1.2021.9.1.10.1
System Uptime: .18.104.22.168.22.214.171.124.0
I m looking more on hardware monitoring parameters...any information available for that?
I tried this .126.96.36.199.4.1.2021.9.1.8.1 but the AIX devices I have is showing OID not supported.
I would get onto ibm, this is weird behavior in my view. When i did it i had no problem in retrieving values.
Yes I have requested the Unix admin to check on this...could be that the SNMU sub agents are not enabled or some other issue....
Should not need an agent to be fair, as long as snmpconf -i has been configured correctly for all oid with no restriction and service snmpd restart has been run, you should have no problem doing an snmp walk.
I am waiting for the admin team to respond..will reply back once I get some useful info...