cancel
Showing results for 
Search instead for 
Did you mean: 
Create Post
Level 7

IP SLA Installation

Hi

I want to install the IP SLA on dedicated server without other Solarwinds packages, i mean i want to put the IP SLA manager on didicated server, can i do that??

Regards


0 Kudos
64 Replies
Level 8

Hi

Thank you for the response

but what are the consequences to write to operation ?


Bilel

0 Kudos

Hi Bilel,

what do you mean by the consequences? IPSLA Manager uses exactly the same syntax as you would use directly through Cisco CLI.

0 Kudos

Hi

I speak of consequence on my network architecture for IP SLA if written command, behind me I just do not take the risk that my network architecture falls.

So I'd like to know what I risk behind setting up IP SLA?

Hoping to have understood!


Bilel

0 Kudos

Hi,

there should not be any risk behind setting up IP SLA on your network. IPSLA operations have a minimal impact on network health. The only problem could be when you set up operations to be tested too frequently or you have a lot of overlapping operations on the same paths.

You may take a look into the IPSLA admin guide page 24 - "Understanding the Impact IP SLA Operations" where you may see a model situation.

thanks,

Michal

0 Kudos

You may take a look into the IPSLA admin guide page 24 - "Understanding the Impact IP SLA Operations" where you may see a model situation.

0 Kudos

Hi

Could you send me the link directly
thank you
Bilel

0 Kudos

Thank you

Bilel

0 Kudos
Level 8

Hi


The question one very important:


I have a question to ask yourself:
What commands exactly as written IPSLA?
And it is the consequence?



The question two very important:

What are the equipment that are supported by IP SLA ?


thank you
Bilel

0 Kudos
Level 16

Hi

If you plan to run alot of IPSLA (SLX)  operation you probebly need to check with support what is the maximum

You could run into some problem there.

0 Kudos

Just to clarify, we do not support IPSLA inside an MPLS network. You must apply IPSLA to the CPE (MPLS edge). That is where you can specify which VFR to use in the IPSLA manager wizard.

0 Kudos

So do you mean by this that the IP SLA statistics can be gotten at the edge of the MPLS network??

I mean from PE router to PE router??

Wael Hilal

IP Planning Supervisor | IP Core Planning | Strategic Planning & Development Directorate

Phone: +970 9 2301056

Mobile: +970 59 2221056

E-Fax: +970 9 2001056

PALTEL- Palestine Telecommunications Company

P.O. Box: 1570, Nablus, Palestine

www.PALTEL.ps<http://www.paltel.ps/>

P Please do not print this email unless it is absolutely necessary. Save a tree.

0 Kudos

Not sure what you mean by PE router to PE router. Ipsla statitics is collected on the router you configure it, and nowhere else.


0 Kudos


Typically the PE is the edge of the MPLS network. The WAN connection from the CPE to PE is IP. The MPLS provider will only let you set up operations on the CPE, and sometimes they will not allow that if the CPE is provider managed. If this is the case you can setup the operation on the next router or switch in your LAN (as the source) and choose a router or switch on the remote LAN as the target. These should be as close to the CPE routers as possible. Specify the VRF when you setup the operation. MPLS.jpg

0 Kudos

But what do you mean by CP

0 Kudos
Level 12

Hi Wael,


No, the IPSLAMGR module is not standalone.

You will need to install it above Orion NPM.

Hope that clarifies.

0 Kudos

Hi Andy

Thanks

So if I have now IP SLA installed on top of Orion NPM, and I want to install it on standalone server, this will not work at all ???

Regards

0 Kudos

Yes, IPSLAMGR can't work on its own. It requires Orion NPM.

0 Kudos

Thanks

0 Kudos