This discussion has been locked. The information referenced herein may be inaccurate due to age, software updates, or external references.
You can no longer post new replies to this discussion. If you have a similar question you can start a new discussion in this forum.

  • I have the same error too. I don't see any alarms on the router itself though....

    Manager@GRE-LL16-IR-A> show chassis environment cb
    CB 0 status:
      State                      Online Master
      Temperature                33 degrees C / 91 degrees F
      Power 1
        1.0 V                      992 mV
        1.0 V MQ                  1060 mV
        1.0 V LU                  1069 mV
        1.2 V                     1192 mV
        1.5 V                     1501 mV
        1.8 V                     1795 mV
        2.5 V                     2516 mV
        3.3 V                     3274 mV
        5.0 V                     5104 mV
        5.0 V bias                5033 mV
        12.0 V                   12007 mV

    Manager@GRE-LL16-IR-A> show chassis alarms
    No alarms currently active

    Manager@GRE-LL16-IR-A>

  • Can you open a ticket with support and provide an SNMP walk of the device?

  • Hi Jeff

    I sure did, the ticket is 412891

    Funny about the Juniper MX80 SNMP WALK.

    Michal H from Solarwinds  got the same SNMP walk from me at 10.8.2012

    When SW start working on HH

    Her is the walk Michal got

    Juniper MX80

    show snmp mib walk 1.3.6.1.2.1.25.6.3

    1. hrSWInstalledIndex.2 = 2
    2. hrSWInstalledIndex.3 = 3
    3. hrSWInstalledIndex.4 = 4
    4. hrSWInstalledIndex.5 = 5
    5. hrSWInstalledIndex.6 = 6
    6. hrSWInstalledIndex.7 = 7
    7. hrSWInstalledName.2 = JUNOS Base OS Software Suite [11.4R1.14]
    8. hrSWInstalledName.3 = JUNOS Kernel Software Suite [11.4R1.14]
    9. hrSWInstalledName.4 = JUNOS Packet Forwarding Engine Support (MX80) [11.4R1.14]
    10. hrSWInstalledName.5 = JUNOS Routing Software Suite [11.4R1.14]
    11. hrSWInstalledName.6 = JUNOS Online Documentation [11.4R1.14]
    12. hrSWInstalledName.7 = JUNOS Crypto Software Suite [11.4R1.14]
    13. hrSWInstalledID.2 = 0.0
    14. hrSWInstalledID.3 = 0.0
    15. hrSWInstalledID.4 = 0.0
    16. hrSWInstalledID.5 = 0.0
    17. hrSWInstalledID.6 = 0.0
    18. hrSWInstalledID.7 = 0.0
    19. hrSWInstalledType.2 = 2
    20. hrSWInstalledType.3 = 2
    21. hrSWInstalledType.4 = 2
    22. hrSWInstalledType.5 = 2
    23. hrSWInstalledType.6 = 4
    24. hrSWInstalledType.7 = 2
    25. hrSWInstalledDate.2 = 07 dc 06 0b  09 0e 35 00  2b 02 00
    26. hrSWInstalledDate.3 = 07 dc 06 0b  09 0f 29 00  2b 02 00
    27. hrSWInstalledDate.4 = 07 dc 06 0b  09 0f 37 00  2b 02 00
    28. hrSWInstalledDate.5 = 07 dc 06 0b  09 10 12 00  2b 02 00
    29. hrSWInstalledDate.6 = 07 dc 06 0b  09 10 00 00  2b 02 00
    30. hrSWInstalledDate.7 = 07 dc 06 0b  09 0f 31 00  2b 02 00
  • Hi

    Problem is in the MX80 
    jnxOperatingState oid that getting back to NPM with  status 6 =down.

    Open ticket with JTAC 2012-1207-0304 - B7461

  • fik to that isue

    JUNOS Versions: 11.3R7   11.2R7 12.1R3   11.4R4   10.4R11 12.2R1   12.3R1