This discussion has been locked. The information referenced herein may be inaccurate due to age, software updates, or external references.

You can no longer post new replies to this discussion. If you have a similar question you can start a new discussion in this forum.

IP Address View

AndrewW over 14 years ago

Is it possible for the user to change how many addresses are listed in the IP Address view? Flipping through the pages slows me down.

0 Peter.Cooper over 14 years ago

Since we don't know how many custom fields people might add, we put the page size at a conservative 100. There is a way to change the number of items that appear in the right-side of the Subnets and IP address management page.
open c:\inetpub\solarwinds\orion\ipam\subnets.aspx
Search for
pageSize="100"
Replace with
pageSize="256"
Note: There are two such entries, change them both.
This will be reverted after running Orion's configuration wizard + website, or when applying a service pack, but it's easily redone. If you find the performance not where you want it, you may need to try a few different values.
Cancel
Vote Up 0 Vote Down

Cancel
0 AndrewW over 14 years ago in reply to Peter.Cooper

That worked great. Thank you.
Cancel
Vote Up 0 Vote Down

Cancel
0 AlbanyNYMike over 14 years ago in reply to AndrewW

Thanks Peter. I was wondering the same thing and Andrew and was about to post. Your workaround works great.
It was terrible when you would be on page 5, make a change, and it shoots you back to page one. Now all my IPs in the range are listed on one page!
Yeah, the page takes a few extra seconds to load, but the beniefit is well worth it.
Thanks!
Cancel
Vote Up 0 Vote Down

Cancel
0 FormerMember over 14 years ago in reply to AlbanyNYMike

Thanks Peter. This workaround is an improvement but can the panel be resized to show more than 13 addresses in the view?
Cancel
Vote Up 0 Vote Down

Cancel
0 bshopp over 14 years ago in reply to FormerMember

Can you explain further what is happening? Only 13 addresses are showing at a time?
Cancel
Vote Up 0 Vote Down

Cancel
0 smcdonald over 14 years ago in reply to Peter.Cooper

This is great - can we get this put into some preference settings for IPAM? Perhaps along with settings to adjust the thresholds for whats Red/Yellow/Green for % of free IPs left?

Thanks!
Cancel
Vote Up 0 Vote Down

Cancel
0 CS_LIU over 14 years ago in reply to smcdonald

THANK YOU !!!!!!
Cancel
Vote Up 0 Vote Down

Cancel
0 FormerMember over 14 years ago in reply to bshopp

Can you explain further what is happening? Only 13 addresses are showing at a time?

Peter,
Here is a snapshot of the Network View. I miscounted. Only 12 networks are shown at a time in the panel. I would like to see the capability to configure both the left and right panels as to the number of rows/networks displayed in the panel view.
Cancel
Vote Up 0 Vote Down

Cancel
0 FormerMember over 13 years ago in reply to FormerMember

We now have 2.0 installed and still no improvements from what I can see to the left and right panels as far as being able to increase/customize the number of rows in the right panel. Oh, yes there has. Instead of 12, I now see 15 rows. Can this be adjusted to view 256 rows without having to scroll the panel?
In the left panel, still can't resize the Description column. Only 20 chars viewable.
Cancel
Vote Up 0 Vote Down

Cancel
0 shannon.snyder over 13 years ago in reply to Peter.Cooper

open c:\inetpub\solarwinds\orion\ipam\subnets.aspx
Search for
pageSize="100"
Replace with
pageSize="256"
Note: There are two such entries, change them both.

Made these changes in attempts to change the IP Address View however still am shown the first 100 lines.
Cancel
Vote Up 0 Vote Down

Cancel