How to calculate the % in Solarwinds IP SLA operation??

Hi,

How to calculate the things below in percentage?

1) packet loss

2) latency

I found a discussion stating the % in NPM is calculate by the last 10 ICMP packets. However,  I can see packet loss is 6%, then what is the base ?

Snap00.jpg

Thnaks in advance

Parents
  • First, the discussion you are referencing (if it is the one I remember seeing a while back) was specific to how NPM sends ICMP packets to nodes, and how many of those packets are used to calculate metrics. This is not to be confused with Cisco IP SLA operations, which are generated and processed between routers. The difference is subtle, but extremely important.

    Secondly, ICMP and UDP Jitter operation types have a default of 10 packets sent per operation. You can however change this at will by using the num-packets command in IP SLA template configuration mode. I have entered an excerpt from the Cisco Command Reference for your review below.

    It would be safe to assume that the base of the calculation you are referencing in your chart is always the default 10. But I would highly recommend verifying this on your router configuration to ensure that a non-default entry has not been made.

    If default, then you can rely on the following:

    • 10 packets are sent between routers during each processed IP SLA Jitter-type operation (TCP or UDP)
    • Every time stamp in your result-set represents a base of 10
    • 60% packet loss = 6 out of 10 packets were lost in transmission (reasons may vary depending on the environment)

    Cisco IOS IP SLAs Command Reference - I through P [Support] - Cisco

    num-packets

    To specify the number of packets for a jitter operation in an auto IP Service Level Agreements (SLAs) operation template, use the num-packetscommand in the appropriate submode of the IP SLA template parameters configuration mode. To return to the default, use the no form of this command.

    num-packets packet-number

    no num-packets

    Syntax Description

    packet-number

    Number of packets to be sent in each operation. Range is 1 to 60000. Default is 10 per operation.

    Command Default

    Default is 10 packets.

    Command Modes

    IP SLA Template Parameters Configuration

    ICMP jitter configuration (config-icmp-jtr-params)

    UDP jitter configuration (config-udp-jtr-params)

    Command History

    Release

    Modification

    15.1(1)T

    This command was introduced.

    Usage Guidelines

    This command changes the number of packets sent during a jitter operation from the default (10) to the specified number of packets.

    You must configure the type of IP SLAs operation, such as User Datagram Protocol (UDP) jitter or ICMP jitter, before you can configure any other parameters of the operation.

    Before you can use this command to configure auto IP SLAs operation templates, you must enter the parameters command in IP SLA template configuration mode.

    Examples

    The following example shows how to configure an auto IP SLAs operation template for an ICMP jitter operation to change the number of packets from the default to 20 packets:

    Router(config)#ip sla auto template type ip icmp-jitter 1 Router(config-tplt-icmp-jtr)#parameters Router(config-icmp-jtr-params)#num-packets 20 Router(config-icmp-jtr-params)#end Router# show ip sla auto template type ip icmp-jitter IP SLAs Auto Template: 1 Measure Type: icmp-jitter Description: IP options: Source IP: 0.0.0.0 VRF:    TOS: 0x0 Operation Parameters: Number of Packets: 20   Inter packet interval: 20 Timeout: 5000           Threshold: 5000 Statistics Aggregation option: Hours of statistics kept: 2 Statistics Distributions options: Distributions characteristics: RTT Distributions bucket size: 20 Max number of distributions buckets: 1 Reaction Configuration: None 

    Related Commands

    Command

    Description

    ip sla auto template

    Begins configuration for an IP SLAs operation template and enters IP SLA template configuration mode.

    show ip sla auto template

    Displays configuration including default values of an auto IP SLAs operation template.

    -ZackM

    Loop1 Systems: SolarWinds Training and Professional Services

  • Hi Zack,

    Thank you for the information.

    I believe my IP SLA operations setting on the router is using default setting -- 10 packets are sent between routers during each processed.

    If the base is 10, then the % in the graph should only be showing 10%,20% , etc. ( multiple of 10%.  )

    And why would I have sth 6%, 8% in the graph?

    Thanks in advance

Reply
  • Hi Zack,

    Thank you for the information.

    I believe my IP SLA operations setting on the router is using default setting -- 10 packets are sent between routers during each processed.

    If the base is 10, then the % in the graph should only be showing 10%,20% , etc. ( multiple of 10%.  )

    And why would I have sth 6%, 8% in the graph?

    Thanks in advance

Children
No Data