Media Gallery - File List
  • HP-OfficeJet-InkLevel

    Hi everyone, Here is a pollers for the HP Officejet series, each assigned to different color. assign all of them to a Officejet Printer and then you can add it into a table like that : While maximum value on each printer type can change, you can see the max level by polling the following oids: = max magenta = max cyan = max yellow = max black Have fun
    • 10 Jul 2017
  • Cisco ASA Hardware Health & failover status monitoring

    *****UPDATE:- HARDWARE HEALTH IS INCLUDED IN NPM 12.2 PLEASE UPGRADE**** IF HARDWARE HEALTH IS MARKED AS CRITICAL ITS KNOWN ISSUE AND DEVELOPMENT TEAM IS CURRENTLY WORKING ON THIS Hello Everyone. In this article i have combined the required steps and information in order to monitor the Cisco Cisco ASA Hardware Health and fail-over status in Orion as work around . If you have any difficulty please let me know . Please Note : I have Cisco ASA 5506 and result may differ depending on the version and...
    • 11 Jun 2017
  • PaloAltoPollers

    Here are the current Palo Alto Pollers I am using.
    • 25 May 2017
  • Synology Inc. Universal Device Poller

    UnDP to collect the following: cpuFanStatus diskID diskModel diskStatus diskTemperature diskType modelName powerStatus raidName raidStatus serialNumber systemFanStatus systemStatus temperature version Based on Synology MIBs: SYNOLOGY-DISK-MIB SYNOLOGY-RAID-MIB SYNOLOGY-SYSTEM-MIB
    • 20 May 2017
  • SOLIDServer BIND Pollers

    This set of UnDPs will poll for the following BIND statistics from a SOLIDServer DNS appliance: bind_authans bind_dropped bind_nonauthans bind_nxdomain bind_nxrrset bind_recurserej bind_recursion bind_referral bind_requestv4 bind_requestv6 bind_srvfail bind_success bind_tcp
    • 15 May 2017
  • Netman or RFC1628 UPS UnDP

    A Universal Device Poller for Netman 204 that uses RFC1628 mib for presenting the information. Will probably work for several types of hardware that use the rfc's mibs. Starting at Containing: upsAlarmsPresent upsBatteryStatus upsBatteryTemperature upsEstimatedMinutesRemaining upsOutputSource upsSecondsOnBattery
    • 4 May 2017
  • Eaton UPS Custom Poller

    Let me know how this works out for you.
    • 27 Apr 2017
  • Buffalo TeraStation Pollers

    Custom SNMP pollers to monitor Buffalo TeraStations. Array Pollers nasArrayStatus. Indicates the current RAID mode/status of an array. Returned values: Not Supported, No RAID Configured, RAID 0, RAID 1, RAID 5, RAID 6, RAID 10, RAID 50, RAID 51, RAID 60, RAID 61. nasArrayCapacity. The capacity of the RAID array in Gigabytes. The capacity cannot be obtained if the RAID array is not configured, not mounted, has LVM enabled, or configured as an iSCSI volume. In such cases, the value -1 will be returned...
    • 2 Mar 2017
  • Silver Peak UnDP

    We have some Silver Peak devices deployed so I created some custom pollers for them.  This UnDP polls the following: ActiveAlarmCount OperStatus ProductModel SystemUptime SystemUptime (Translation of time ticks to days) SystemVersion
    • 20 Jan 2017
  • Ruckus Client count

    Attached is my first pass at pulling the Number of clients connected to our Ruckus Access Points. There are 3 pollers: ruckusRadioStatsNumSta - table with number of 2.4G and 5G connected clients / ruckusRadioStatsNumSta24 - single Get to allow charting just the 2.4G clients on the AP / RuckusAP5Ghz - this is a transform that takes the total number of connections, subtracts the 2.4 clients and presents a single number that can be charted. This allows me to have a running historical chart of the 2...
    • 29 Dec 2016
  • ICX Stack Details

    Poller for Brocade ICX stacks that retrieves: serial number unit state unit type unit role unit firmware
    • 11 Oct 2016
  • ICX stack pwr fan temp Poller

    Poller that gets stack unit Power supply and fan status and unit temperature
    • 11 Oct 2016
  • Cisco ASA 9.6 VPN Pollers

    I'm running Cisco ASA Version 9.6(1)10.  Here's the VPN Pollers tweaked a little, along with some notes I compiled while trying to find these, and research them a bit and get them to work.  Hope this helps. The "main" OID for VPN stats is: Very helpful MIB website: ==================== I found this, in the mib walk: . = OID: . = OID: 1...
    • 7 Oct 2016
  • Palo Alto Active VPN Tunnels UnDP

    Hello, You can assign the attached UnDP to fetch the information of active VPN Tunnels for Palo Alto.
    • 4 Oct 2016
  • Cisco License Management Poller

    Uses the clmgmtLicenseInfoTable values from the ciscoLicenseMgmentMIB - clmgmtLicenseFeatureVersion - clmgmtLicenseType - clmgmtLicenseCounted - clmgmtLicenseValidityPeriod - clmgmtLicenseValidityPeriodRemaining - clmgmtLicenseExpiredPeriod - clmgmtLicenseMaxUsageCount
    • 12 Jul 2016
  • Multiple APC NetBotz Environment Monitor

    This is actually a very repetitive UnDP, specifically for APC NetBotz devices. This could be helpful when you have many temperature monitors plugged into the same device and need to create an individual UnDP for each one, this has the original value, and a transform into Fahrenheit. If node abc has 2 tempmons, and node xyz has 2 tempmons as well, they both are the same OID so one UnDP is less than ideal unless it can be correlated to the Location or Name OID somehow -- requires some SQL knowledge...
    • 27 Jun 2016
  • Cisco Wireless Controller 5500 Power Supply Status Pollers ~ CiscoWireless5500-PowerSupply.UnDP

    ***New upload has readable values.  True/False for Power Supply presence, and Up/Down/Unknown for operational status*** These are Universal Device Pollers - import these into your UnDP on the Server; do not import via the new poller web interface.   - you can find a hardware health for the Wireless controllers that includes the OS Version details(and still under construction) under the new Pollers So after many attempts to find Power Supply Pollers I was able to find the needed details to slap these...
    • 5 May 2016
  • Wireless_Rogue_AP_Detection

    Even though Wireless Rogue detection is built into NPM Wireless Polling, it weirdly only gives you the WLC that detected the Rogue AP, not the actual Access Points that discovered the Rogue signal, even though in the SNMP MIB's all of that data is gathered.  Often I have clients who use a single WLC to manage APs in multiple sites.  Knowing which AP on the WLC detected the rogue signal is imperative for this feature to be useful.  Unless of course I'm missing something and its there and I completely...
    • 22 Jan 2016

    I created a SNMP-NET UnDP before and it was working pretty well, but we've recently started transitioning to the new NV6 Cards. Here are the 5 of them that I have working for both SNMP-NET and NV6 Cards. The input and output voltage1 will need to be added in order to do the calculation to put the reformatted version of input/outputs. Contains: dupsInputVoltage1 dupsOutputVoltage1 MMBatteryCondition MMEstimatedTime (In Minutes) MMInputVoltage (In Volts) MMOutputVoltage (in Volts) MMOutputLoad (in...
    • 6 Jan 2016
  • Cisco UCS Active Hardware Alerts in Solarwinds

    By using below UnDP, we can get Cisco UCS Active Hardware Alerts in Solarwinds.
    • 28 Nov 2015